Is Coda and related terms NOT a function of this software?

[Robert lang]

Is Coda and related terms NOT a function of this software?

[Fred28]

The program does allow you to Create repeat symbols like Segno and Coda. You might want to check the user´s manual here:

Contents (nchsoftware.com)

[Robert lang]

Yes, but the manual does not mention the terms by name, they have a backhanded reference to repeats.  So, if you search for the content, you get NO results.  I offer, name the content in the user manual by the term being used.  A search on CODA SHOULD then show CODA.

 

Thank You!

[JackE]

On 2/26/2021 at 11:12 PM, Fred28 said:

The program does allow you to Create repeat symbols like Segno and Coda. You might want to check the user´s manual here:

Contents (nchsoftware.com)

If this info is in the manual, it would be helpful if you'd specified which section, rather than just saying "check the manual" - or, better still, specified how we can create those symbols.  I've read through the manual very carefully, twice, and the only reference I can find is in the introduction, which says the software allows you to:
"Create repeat symbols like Segno and Coda"

Unfortunately, it doesn't say how you can do this, nor where to find the instructions, nor can I find any other reference in the user manual to either Segno or Coda.

Edited September 11, 2021 by JackE
Found additional info referring to this topic.

[Fred28]

You should be able to open the program, right click on a staff and hover your mouse over REPEAT  and here you will see the options CODA or TO CODA.

[JackE]

1 hour ago, Fred28 said:

You should be able to open the program, right click on a staff and hover your mouse over REPEAT  and here you will see the options CODA or TO CODA.

Thank you, Fred28 - I discovered this quite by accident last night.  It's a pity that the company didn't explain this in the 'Help' files - so I will send them an e-mail suggesting they add it.

With best regards,

Jack

[Robert lang]

On 9/11/2021 at 6:21 PM, JackE said:

If this info is in the manual, it would be helpful if you'd specified which section, rather than just saying "check the manual" - or, better still, specified how we can create those symbols.  I've read through the manual very carefully, twice, and the only reference I can find is in the introduction, which says the software allows you to:
"Create repeat symbols like Segno and Coda"

Unfortunately, it doesn't say how you can do this, nor where to find the instructions, nor can I find any other reference in the user manual to either Segno or Coda.

LOVE IT.  ANd have they fixed this??????  EFFING AYE NO!!!!!

[Robert lang]

On 9/11/2021 at 6:21 PM, JackE said:

If this info is in the manual, it would be helpful if you'd specified which section, rather than just saying "check the manual" - or, better still, specified how we can create those symbols.  I've read through the manual very carefully, twice, and the only reference I can find is in the introduction, which says the software allows you to:
"Create repeat symbols like Segno and Coda"

Unfortunately, it doesn't say how you can do this, nor where to find the instructions, nor can I find any other reference in the user manual to either Segno or Coda.

My Point, exactly.  It is in a pull-down menu, but, as I type, I forget which pull down carrot to use.  If I can figure out how to find it, now, and return to type here, I will.

 

Ah, within a measure, right click and you should get a drop-down menu.  TWELVE items down is "repeat", or from the bottom see, Measure Layout, Measure, and then, REPEAT.  Click on REPEAT and see the various Coda, Capa Da Segno etc., options.