The 'control' shortcuts do not work over Terminal Services ie when the focus is within TS.
I have a program (TSRemoteExec) that does a 'call-back' to the originating PC from within TS for auto-dialling:
"C:\Temp\TSRemoteExec.exe ""C:\Program Files\NCH Swift Sound\Talk\talk.exe"" -dial " & "1831" & strCallNumber
'-dial' is the parameter.
Is there one for 'Hang-up' and maybe others?
Telstra charge about 27c/min plus flag fall to non-Telstra and less to Telstra phones. I am on a 10.4c per minute 'test' plan but the VOIP provider is very bad. I have a 'dormant' 18c/min account and have started to use them. So sorry your rates would be too high. But I wish you the very best with your new service.
Anyway after switching to this VOIP most mobile calls are auto-disconnecting but landlines are not - go figure.
OK I'll keep digging thanks.
Problem is that I'm using not using a router but "Internet Connection Sharing" (temporarily for a few mths) and have checked the "delivery of ICS PC" and cannot see any firewall.
Maybe ET has problems with ICS networks?
Anyway pythonpoole I filled the survey and noticed your logo at the end (Skorptec). So you're starting up a VOIP service I presume - I don't think you're going public (listing on the stock exchange) and laying cables - anyway all the best.
PS - did you develop ET and other related telephony products - if not then would you mind telling me who did.
I have just checked and double-checked: On my PC I disconnected Norton's AV and on the PC with Internet Connection Sharing there is no firewall nor AV.
BTW what does "Unable to auto-detect public IP. Using private IP" mean?
OK so I ran the Network Wizard and it set up the 2 STUN servers. 'stun.softjoys.com' and 'stun1.faktortel.com.au'.
Now when I make a call I get the following messages - the call goes thru but ET will not auto-disconnect.
06:40:37 Initiated sip call to: 61404795165
06:40:38 STUN server failed: stun.softjoys.com
06:40:39 STUN server failed: stun1.faktortel.com.au
06:40:39 The internet connection could be down.
06:40:39 Check local firewall is not blocking UDP port 8000
06:40:39 Also check STUN settings or use different STUN servers.
06:40:39 Unable to auto-detect public IP. Using private IP
06:40:39 STUN server failed: stun1.faktortel.com.au
06:40:39 STUN server failed: stun1.faktortel.com.au
06:40:39 The internet connection could be down.
06:40:39 Check local firewall is not blocking UDP port 5060
06:40:39 Also check STUN settings or use different STUN servers.
06:40:39 Unable to auto-detect public IP. Using private IP
06:40:40 SIP Public IP is: 192.168.0.2:5060
06:40:40 SIP Number: 61390920596@192.168.0.2:5060
06:40:48 Call answered
06:41:06 Call has disconnected
I have set up ET on 4 PCs. 3 work fine but the 4th. has no audio inbound.
During the setup the ET Wizard said that a Firewall was blocking UDP port 5060,5070, 8000 etc.
I have no firewall on that PC and ALL PCs access the Internet thru the same router.
Any ideas about how to set up Express Talk so I can talk to someone on anothet PC that has ET>
I have looked everywhere on the NCH website FAQs but no mention of this.
I have Express Talk (free) installed on 4 PCs and 3 work fine.
On 1 PC I cannot HEAR anything over VOIP but when I use the "Audio Setup Wizard" all is well.
All the options (in Exp Talk) on all the PCs are EXACTLY the same.
I have run out of ideas.
Could the router be blocking something?
I have Express Talk (free) installed on 4 PCs and 3 work fine.
On 1 PC I cannot HEAR anything over VOIP but when I use the "Audio Setup Wizard" all is well.
All the options (in Exp Talk) on all the PCs are EXACTLY the same.
I have run out of ideas.
Could the router be blocking something?
I can call out no problems; didn't mention that before.
I do have a static IP address.
Is it used for incoming calls? There will be none.
So is it worth setting up?